| What this describes | A common metric thread connecting the thermostatic head to a compatible valve body. | A different metric thread used by some valve and head combinations. | A push-fit or clip-on head connection designed for a specific valve interface. | A thermostatic head whose temperature sensor is positioned away from the valve body, often using a capillary tube. | A battery-powered or powered actuator that controls the valve electronically; connection type depends on the model. |
| Typical compatibility | Compatible only when the valve body has the matching thread and the head’s stroke and closing force suit that body. | Compatible only with a matching M28 × 1.5 valve interface and suitable operating characteristics. | Compatible with the specified clip-on valve interface; appearance alone is not enough to confirm a match. | Requires a matching valve-head interface, just like a standard mechanical head. | Requires a compatible valve interface and confirmation that the actuator supports the valve’s required travel and force. |
| Interchangeability | Often widely available, but the thread alone does not guarantee functional compatibility. | Not interchangeable with M30 × 1.5 without a suitable, verified adapter. | Generally not interchangeable across different clip-on systems unless an approved adapter is specified. | Sensor placement differs; the remote sensor does not make an incompatible head connection fit. | Varies by product. Some electronic heads use common threaded interfaces; others require adapters or a dedicated valve body. |
| Temperature sensing | Sensor is usually integrated into the head and measures air near the radiator. | Sensor is usually integrated into the head and measures air near the radiator. | Usually integrated into the head; confirm the installation position and manufacturer instructions. | Remote sensor measures room air away from heat trapped behind curtains, covers, or furniture. | May use an onboard sensor, a remote sensor, or both, depending on the model. |
| Typical control range | Many mechanical TRV heads offer settings spanning roughly 6–28°C, but available ranges and scale markings vary by model. | Setpoint range is model-dependent; remote sensing can improve room-temperature measurement where the radiator is obstructed. | Setpoint range, scheduling, and control precision depend on the model, app, and control system. |
| Frost-protection setting | Many mechanical heads include a frost-protection position, commonly intended to maintain a low temperature around 6–8°C; verify the specific product specification. | May include frost protection; check whether the setting applies to the remote sensor’s measured temperature. | May provide configurable frost protection, but behavior can depend on power, connectivity, and system settings. |
| Radiator-side connection | Separate from the head-to-valve interface. Check the valve body’s radiator-tail connection, pipe size, and fitting type. Common arrangements include threaded connections and compression fittings; regional practices differ. |
| Flow direction and pipe layout | Check the valve body’s flow-direction marking and installation instructions. Not every valve is suitable for every flow direction or pipe arrangement; reverse-flow noise or poor control can occur with an unsuitable installation. |
| System and operating limits | Confirm the valve body’s specified pressure, temperature, flow capacity, and water-quality requirements against the heating system. These limits are model-specific and cannot be inferred from the head connection. |
| Performance reference | EN 215 is a European performance standard for thermostatic radiator valves. Check the product’s declared compliance and test information; the standard does not make different connection interfaces interchangeable. |
| Best comparison checks for buyers | Confirm thread size, valve stroke, closing force, temperature range, and adapter requirements. | Measure or verify the thread; do not assume a visually similar head will fit. | Identify the exact valve interface and confirm any adapter is intended for that combination. | Check capillary length, sensor placement, mounting method, and head-interface compatibility. | Check interface and adapter, power source, control method, connectivity needs, manual override, and replacement availability. |
| Practical suitability | A useful option where the existing valve body has a verified matching interface and replacement parts are readily available. | A suitable replacement when the existing valve body specifically requires this interface. | Useful for matching an existing dedicated valve system; verify parts availability before purchase. | Useful when the radiator or head is enclosed or exposed to a local heat source that can distort the sensed room temperature. | Useful where scheduling or remote control is required and the heating system, network, and power arrangements are compatible. |
| Global buyer caution | Before ordering, identify the existing valve-body make and interface from its markings or measurements, distinguish the head connection from the radiator-pipe connection, and confirm the seller’s compatibility list. Regional thread conventions and product specifications vary. |