| 1 | PE black masterbatch Film, pipe, sheet, or molded-part applications | Often screened around 1–5% by weight; the required loading depends on carbon-black content, opacity, and end use. | Request the numerical MFR and test conditions. Compare values only when method, temperature, and load match the processing requirement. | TDS, certificate of analysis (CoA), carbon-black content, dispersion assessment, and batch-to-batch color or appearance checks. | Confirm applicable market and end-use requirements; request declarations and supporting test reports for the exact grade. | Dispersion, jetness or opacity, filter pressure, process stability, and consistency between lots. |
| 2 | PE white masterbatch Film, packaging, sheet, or injection molding | Often screened around 2–5% by weight; opacity, titanium dioxide concentration, and film thickness affect the dosage. | Ask for MFR measured by ISO 1133-1 or ASTM D1238, with the test temperature and load stated; assess compatibility with the base resin. | TDS, CoA, pigment content, color or whiteness data, and dispersion results using a stated method. | For food-contact or other regulated uses, verify the specific formulation, intended use, and destination-market documentation. | Opacity at target thickness, color consistency, plate-out, and impact on film or part properties. |
| 3 | PE color masterbatch Custom colors for film, extrusion, or molding | A common trial range is about 1–4% by weight; the required level depends on pigment strength and the color specification. | Check the grade’s stated MFR and method; also confirm the carrier resin and suitability for the selected PE process. | Color standard or approved plaque, TDS, CoA, and agreed color tolerance measured under consistent conditions. | Request applicable substance, restricted-material, and end-use declarations for the actual color formulation. | Color match, repeatability, dispersion, weathering needs, and minimum order quantity for custom colors. |
| 4 | UV-stabilizer masterbatch Outdoor film, agricultural film, or exposed products | Often trialed around 1–3% by weight, but required loading varies with stabilizer chemistry, exposure, and product design. | Compare MFR under identical test conditions and check that the carrier is compatible with the PE grade and production process. | TDS, CoA, active-ingredient information where available, and agreed weathering or durability test data for the intended application. | Review chemical and market-specific requirements; do not treat a general compliance statement as proof for every end use. | Outdoor lifetime target, compatibility with other additives, color change, and evidence from relevant exposure testing. |
| 5 | Antioxidant masterbatch Thermal processing and longer-term stabilization | A preliminary trial may fall around 0.5–2% by weight; follow the grade supplier’s recommendation and validate in the finished application. | Request MFR values and test conditions; evaluate whether the concentrate disperses without adversely changing the finished resin’s flow behavior. | TDS, CoA, processing guidance, and thermal-aging or oxidation-performance data relevant to the application. | Verify the permitted chemistry and documentation for the destination market and intended use, especially for food-contact applications. | Processing history, color stability, additive interactions, and repeatability at the target dosage. |
| 6 | Slip masterbatch PE film applications requiring lower surface friction | Common initial trials are about 1–3% by weight; the final level depends on the active additive and target coefficient of friction. | Compare MFR using the same method and conditions; confirm that the carrier and concentrate feed consistently on the film line. | TDS, CoA, coefficient-of-friction test method and results, and any migration or surface-performance data relevant to use. | Check intended-use restrictions and food-contact documentation where applicable; verify the exact additive grade. | COF over time, blocking, printability, sealing performance, and any additive transfer concerns. |
| 7 | Antiblock masterbatch Film winding and separation performance | Often screened around 1–5% by weight; particle type, film structure, and desired antiblock level influence the dosage. | Ask for MFR with stated test conditions and check for stable feeding and uniform additive distribution in the film. | TDS, CoA, particle or mineral information, and agreed blocking, haze, or surface-performance measurements. | Request market-specific declarations and supporting information for the additive and its intended application. | Blocking reduction versus haze, surface appearance, film clarity, and impact on sealing or printing. |
| 8 | Processing-aid masterbatch Film extrusion and melt-processing support | A preliminary trial may be around 0.5–2% by weight; use the grade-specific recommendation and confirm performance on the target line. | Compare measured MFR under identical conditions and request guidance on dose, start-up, and any conditioning period. | TDS, CoA, processing recommendations, and application-specific evidence such as melt-fracture or surface-quality observations. | Confirm formulation and declarations against the destination-market rules and the product’s end use. | Output, surface quality, die build-up, start-up behavior, and possible effects on downstream printing or sealing. |
| 9 | Antistatic masterbatch Packaging film and molded PE products | A broad initial screening range is about 1–5% by weight; performance depends on chemistry, humidity, and product design. | Obtain the MFR, method, and test conditions; verify compatibility with the base resin and the required processing route. | TDS, CoA, surface or volume resistivity test method, conditioning conditions, and performance data for the target environment. | Check applicable chemical restrictions and intended-use documentation; assess any migration-sensitive requirements. | Electrical performance over time, humidity sensitivity, surface appearance, and interactions with printing or sealing. |
| 10 | Desiccant masterbatch Moisture reduction for selected recycled or damp feedstocks | Often trialed around 1–5% by weight; dosage depends on feedstock moisture, process conditions, and the supplier’s grade recommendation. | Request MFR and conditions, then trial for stable extrusion and compatibility with the actual resin blend. | TDS, CoA, moisture-handling guidance, and agreed checks of bubbles, surface defects, or other process outcomes. | Request composition and applicable declarations for the intended market and finished-product use. | Performance at measured feedstock moisture, dispersion, process stability, and effect on finished-part properties. |