| 1 | 3/2 Normally Closed, Spring Return | 3/2 NC | 3 ports / 2 positions | Foot pedal / spring return | Usually 0–10 bar | G1/8, G1/4, or NPT equivalent | At rest, supply port 1 is blocked and outlet port 2 exhausts through port 3; when pressed, port 1 connects to port 2. | Single-acting cylinders, air blow-off, clamps, and start/stop pneumatic controls. |
| 2 | 3/2 Normally Open, Spring Return | 3/2 NO | 3 ports / 2 positions | Foot pedal / spring return | Usually 0–10 bar | G1/8, G1/4, or NPT equivalent | At rest, port 1 connects to port 2; when pressed, the supply path is interrupted and port 2 exhausts through port 3. | Release-on-press controls, operator presence functions, and circuits requiring air flow in the normal position. |
| 3 | 3/2 Normally Closed, Detented | 3/2 NC, maintained | 3 ports / 2 positions | Foot pedal / mechanical detent | Usually 0–10 bar | G1/8 or G1/4 | The selected spool position remains after the pedal is released until the pedal is pressed again or the detent is reset. | Manual mode selection, fixture control, and applications where continuous foot pressure is undesirable. |
| 4 | 3/2 Normally Closed, Guarded Pedal | 3/2 NC with guard | 3 ports / 2 positions | Protected foot pedal / spring return | Typically 0–8 bar | G1/4 or NPT equivalent | The guard helps reduce accidental actuation; the valve returns to its safe exhaust condition when the pedal is released. | Presses, punching equipment, assembly stations, and floor-mounted machinery. |
| 5 | 3/2 Pneumatic Pilot-Assisted Foot Valve | 3/2 pilot-assisted | 3 ports / 2 positions | Foot signal / spring or air return | Commonly 1.5–10 bar | G1/4 to G1/2 | A small pilot signal shifts the main valve element, allowing higher flow than a purely direct mechanical design. | Larger single-acting actuators, pneumatic tooling, and controls requiring reduced pedal effort. |
| 6 | 5/2 Monostable, Spring Return | 5/2, single solenoid or mechanical actuation | 5 ports / 2 positions | Foot pedal / spring return | Usually 2–10 bar | G1/4, G3/8, or G1/2 | Port 1 is the supply, ports 2 and 4 are working ports, and ports 3 and 5 are exhausts; the valve returns to its default position when released. | Double-acting cylinders requiring a defined return position after pedal release. |
| 7 | 5/2 Bistable, Maintained | 5/2, double-actuated | 5 ports / 2 positions | Two foot commands / maintained spool | Typically 2–10 bar | G1/4, G3/8, or G1/2 | The spool remains in its last selected position after the pedal is released and changes state only when the opposite actuation signal is applied. | Reciprocating cylinders, indexing equipment, and applications needing maintained extension or retraction. |
| 8 | 5/2 Guarded Monostable Foot Valve | 5/2, protected pedal | 5 ports / 2 positions | Guarded foot pedal / spring return | Commonly 2–8 bar | G1/4 or G3/8 | The guard limits unintended operation while the spring establishes a repeatable default flow path through the 5/2 circuit. | Machine tools, material handling systems, and floor-operated double-acting mechanisms. |
| 9 | 5/2 Low-Profile Industrial Foot Valve | 5/2 compact mechanical valve | 5 ports / 2 positions | Low-profile pedal / spring return | Typically 2–10 bar | G1/4 or G3/8 | Provides two alternating flow paths for a double-acting actuator while minimizing pedal height in confined work areas. | Assembly benches, packaging lines, compact machinery, and ergonomic operator stations. |
| 10 | 5/2 High-Flow Floor-Mounted Valve | 5/2 high-flow configuration | 5 ports / 2 positions | Heavy-duty pedal / spring or maintained return | Commonly 2–10 bar | G1/2 or larger, depending on design | Uses larger supply, working, and exhaust passages to reduce pressure loss when operating larger double-acting cylinders. | Heavy-duty clamps, industrial presses, lifting mechanisms, and high-cycle pneumatic equipment. |