| Drawing and revision control | Machine to the released 2D drawing and 3D model; identify the governing document and revision. | Specify applicable drawing units, general tolerances, datums, and any model-based definition requirements. | Can the supplier review the full drawing package, identify ambiguous dimensions, and control revisions through production? | Documented drawing review, revision identification on the job traveler, and approval of clarified requirements before machining. |
| Datum reference frame | Locate a mounting face as primary datum A, a locating bore axis as datum B, and a side face as datum C. | Use datum references in feature control frames where the functional relationship requires them. | Does the inspection method establish the same datum reference frame used to define the part’s function? | Inspection plan showing datum setup, measurement alignment, and the features checked relative to A, B, and C. |
| Position of holes | Example: a pattern of four clearance holes located from the mounting face and two locating features. | Define a position tolerance with a diameter symbol and the applicable datum references; state the tolerance value on the drawing. | Can the supplier hold and measure the stated position tolerance using a method suitable for the part size and tolerance? | CMM report or other traceable measurement record listing actual hole locations and the evaluated position tolerance. |
| Flatness of a sealing face | Example: control the flatness of a machined sealing surface where contact across the surface is functionally important. | Specify a flatness tolerance on the surface; flatness is a form control and does not use a datum reference. | Can the supplier select a measurement approach that represents the surface condition and stated tolerance? | Surface measurement results from an appropriate instrument or documented inspection method, with the measurement area identified. |
| Perpendicularity of a bore axis | Example: keep a bore axis perpendicular to a mounting face used as a functional reference. | Apply a perpendicularity control to the axis and reference the relevant datum plane, such as datum A. | Will the supplier inspect the axis relative to the specified datum rather than checking only the bore diameter? | Measurement report showing the bore axis orientation relative to the datum setup. |
| Hole-and-shaft fit | Example: a rotating shaft in a housing bore where a clearance fit is required. | Specify a fit such as H7/g6 when appropriate. ISO 286 fit limits depend on the nominal size and the specified tolerance grades. | Can the supplier manufacture and inspect both mating features to the selected limits, including any required surface finish? | Actual bore and shaft measurements, material or process records where required, and confirmation against the applicable ISO 286 size range. |
| Close-clearance or location fit | Example: a removable locating component requiring small clearance for assembly and repeatable positioning. | A fit such as H7/h6 may be considered, subject to functional analysis and the applicable nominal-size limits in ISO 286. | Does the supplier understand whether the fit is intended to provide clearance, location, or frequent assembly and removal? | Measured size results for both mating components and a fit review based on the applicable ISO 286 tables. |
| Interference fit | Example: a permanent press fit between a shaft and a hub, where assembly force and service conditions are considered. | A fit such as H7/p6 may be considered for some applications; verify the resulting limits for the nominal size and design conditions. | Can the supplier control the mating dimensions and advise whether the specified fit is manufacturable and inspectable? | Recorded dimensions for both parts and, if specified, an assembly procedure or verification record. |
| General dimensional tolerances | Identify critical dimensions individually; use a stated general tolerance standard only for dimensions not otherwise toleranced. | Do not rely on a general tolerance to define a functional fit or a GD&T requirement. | Will the supplier flag dimensions that lack a tolerance or conflict with the stated fit and geometric controls? | Completed drawing review and first-article inspection results for designated critical dimensions. |
| Surface finish | Specify surface texture on functional surfaces such as bearing seats, sealing faces, and sliding interfaces. | State the required surface-texture parameter and value on the drawing; do not infer finish from a dimensional tolerance. | Can the supplier achieve and measure the specified finish on the actual feature and material? | Surface-roughness measurement record where required, with the parameter and measurement location identified. |
| Material and condition | Specify material grade, temper or condition, and any required heat treatment or material certification. | These requirements are separate from GD&T and dimensional fit definitions but can affect machinability and final dimensions. | Can the supplier maintain material identification and account for dimensional changes from heat treatment or finishing? | Material certificate or traceability record, plus relevant process and final-inspection documentation. |
| Inspection capability and reporting | Agree on first-article, in-process, and final inspection requirements before production begins. | Inspection must evaluate the specified dimensions, GD&T controls, and fit limits using appropriate methods. | Are calibrated instruments, trained inspectors, documented procedures, and required reporting available? | Inspection plan, calibration records, first-article report, and final dimensional report as agreed in the purchase specification. |