| Shielded enclosure and panel bonding | Limits radiated emissions and reduces the impact of external electromagnetic fields by controlling enclosure openings, seams, and conductive joints. | Control cabinets, instrumentation enclosures, drive panels, and equipment installed near high-power switching or radio-frequency sources. | Check enclosure material and seams, door bonding, cable-entry treatment, ventilation openings, and continuity between panels. Preserve the specified ingress-protection rating after modifications. | IEC 61000-6-2 and IEC 61000-6-4 may apply to industrial equipment where no more specific product standard takes precedence. IEC 60529 classifies enclosure ingress protection; it is not an EMC performance standard. | Evaluate the complete assembled enclosure, including doors, apertures, connectors, and installed cables. A conductive enclosure alone does not guarantee EMC compliance. |
| EMC line filters | Attenuate conducted high-frequency noise on power or signal lines, subject to correct filter selection and installation. | AC or DC power inputs, motor-drive supplies, switch-mode power equipment, and selected control or measurement circuits. | Match voltage, current, frequency, phase configuration, load type, and protective-earth arrangement. Follow the filter's line/load orientation and installation instructions; verify leakage-current and safety requirements. | Conducted emissions can be assessed under the applicable product or generic emissions standard. IEC 61000-4-6 is a conducted RF immunity test method, not a filter product standard. | Keep unfiltered and filtered wiring separated, use short connections to the bonding surface, and test the installed system. Incorrect mounting or wiring can substantially reduce filter effectiveness. |
| Protective bonding and grounding | Provides low-impedance paths for fault and interference currents and helps reduce unwanted voltage differences between conductive parts. | Machine frames, cabinet doors, mounting plates, cable shields, drive systems, and interconnected industrial equipment. | Coordinate with the electrical safety design and earthing system. Check bonding across painted or removable joints, cable-shield termination, and the manufacturer's grounding instructions. | IEC 60204-1 addresses electrical equipment of machinery, including protective bonding requirements. EMC immunity and emissions are evaluated using applicable EMC standards separately. | Do not treat protective earth, functional earth, and signal reference as automatically interchangeable. Design bonding for both safety and EMC, then verify it in the assembled installation. |
| Surge protective devices | Limits transient overvoltages caused by events such as switching or lightning-related surges on power and signal circuits. | Incoming power supplies, control lines, communication links, and installations exposed to surge disturbances. | Coordinate the device with system voltage, earthing arrangement, upstream protection, expected surge environment, and the circuit's operating characteristics. | IEC 61000-4-5 specifies a surge immunity test method. It does not, by itself, define a universal surge-protective-device selection for every installation. | Use protection appropriate to the port and installation. Check connection length, coordination with other protective devices, and whether protected equipment remains operational after the required test. |
| Transient and burst suppression | Improves immunity to repetitive fast electrical transients and electrostatic discharge at relevant ports or accessible surfaces. | Digital control inputs, relay circuits, operator interfaces, I/O wiring, and equipment exposed to switching of inductive loads. | Identify the affected port, cable length and routing, connected peripherals, and the equipment's reset or recovery behavior. Suppression components must suit the signal and safety design. | IEC 61000-4-4 covers electrical fast transient/burst immunity testing; IEC 61000-4-2 covers electrostatic discharge immunity testing. | Test the equipment in representative operating modes and configurations. Protection should not cause unacceptable signal distortion, excessive leakage, or unsafe component stress. |
| Cable shielding and routing | Reduces coupling between cables and helps contain or reject electromagnetic interference when shield termination and routing are appropriate. | Motor, encoder, analog, fieldbus, and communication cables, especially when routed near power converters or switching conductors. | Confirm cable type and connector compatibility, shield continuity, termination method, separation from noisy circuits, and compliance with equipment and network installation instructions. | Radiated RF immunity is addressed by the IEC 61000-4-3 test method; conducted RF immunity is addressed by IEC 61000-4-6. These are test methods, not cable-selection specifications. | Use a system-level wiring plan. A shielded cable can be ineffective if connectors, terminations, routing, or cabinet entries interrupt the intended shielding path. |
| Equipment-level EMC testing and integration | Identifies interactions among the enclosure, filters, wiring, grounding, software, and connected equipment before deployment. | New machine designs, control-panel changes, drive retrofits, and systems assembled from components with different EMC characteristics. | Test representative operating modes, cable lengths, loads, accessories, and installation conditions. Review component instructions and the system's intended environment. | IEC 61000-6-2 provides generic industrial immunity requirements and IEC 61000-6-4 provides generic industrial emissions requirements when applicable. Product-specific standards may take precedence; IEC 61326-1 applies to specified measurement, control, and laboratory equipment. | Choose standards based on equipment type, intended environment, jurisdiction, and applicable regulations. Component compliance does not automatically establish compliance of the completed machine or system. |